What Is the Right Glacier Bay Faucet Hole Size for Your Sink?

glacier bay faucet hole size
TL;DR: Most Glacier Bay faucets need a standard 1‑3/8 inch (about 35 mm) mounting hole in the deck or sink, and their bathroom and kitchen faucets fit sinks pre‑drilled with 1, 2, 3, or 4 holes on the standard 4‑inch centerset or 8‑inch widespread spacing. If your sink has more holes than your faucet uses, a deck plate (escutcheon) covers the extras.

If you’re trying to nail down the glacier bay faucet hole size before you buy or install, here’s the short version: the mounting hole itself is almost always 1‑3/8″ (35 mm) in diameter, and the number and spacing of holes is what actually decides whether a given faucet fits your sink. Get those two numbers right — hole diameter and hole spacing — and installation goes smoothly. Get them wrong and you’re either drilling porcelain or staring at holes you can’t cover. This guide walks through exactly how to measure, what the standard sizes are, and how to handle the mismatches people run into most.

Glacier Bay is The Home Depot’s house brand, and its faucets are built to the same North American plumbing standards as Moen, Delta, and Kohler. That’s good news for you: the dimensions are standardized, so the numbers below aren’t Glacier Bay quirks — they’re industry norms that Glacier Bay follows.

What size hole does a Glacier Bay faucet need to be drilled?

A standard Glacier Bay faucet needs a 1‑3/8 inch (35 mm) diameter mounting hole. This is the near-universal size for residential faucets in the U.S., so if your countertop, granite, or sink is drilled to 1‑3/8″, the faucet’s threaded shank and mounting hardware will pass through cleanly.

A few things worth knowing about that number:

  • 1‑3/8″ is the target, but a little bigger is fine. Some stone fabricators and sinks come with holes up to 1‑1/2″ (38 mm). Most Glacier Bay faucets tolerate that because the base and gasket sit on top and hide the extra clearance. Going smaller than 1‑3/8″ is the problem — the shank won’t fit.
  • The shank itself is narrower than the hole. The 1‑3/8″ figure is the hole you drill, not the pipe. That gap leaves room for supply lines, mounting studs, and a tightening nut.
  • Vessel and single-hole faucets follow the same rule. A tall vessel-style Glacier Bay bathroom faucet still drops through a 1‑3/8″ hole.

If you’re drilling a hole yourself in stainless steel or a stone/quartz countertop, use a 1‑3/8″ hole saw or diamond hole bit rated for that material, and go slow with water to keep the bit cool. In existing porcelain or ceramic sinks, drilling is risky — cracking is common — so most people match a faucet to the holes the sink already has instead of enlarging them.

How many holes does my sink have, and which Glacier Bay faucet fits?

Count your holes and measure the spacing between the outer two — that tells you which faucet configuration you need. Sinks come pre‑drilled with 1, 2, 3, or 4 holes, and Glacier Bay makes a faucet for each. The most common setups are single-hole, 4‑inch centerset (3 holes), and 8‑inch widespread (3 holes, spread apart).

Here’s how the configurations break down:

Configuration Holes needed Hole spacing (center to center) Best for
Single-hole 1 N/A (one 1‑3/8″ hole) Modern baths, small vanities, most kitchens
Centerset 3 4″ between outer holes Standard bathroom sinks
Widespread 3 8″ to 16″ between outer holes Larger vanities, upscale baths
Mini-widespread 3 4″ Compact sinks wanting a widespread look
Kitchen (with accessories) 1–4 8″ spread typical Kitchen sinks with sprayer/soap dispenser

The single most useful measurement for a bathroom faucet is the distance from the center of the far-left hole to the center of the far-right hole. If it’s about 4 inches, you have a centerset (or mini-widespread) sink. If it’s 6 to 16 inches, you have a widespread sink and need a widespread faucet where the spout and two handles are separate pieces connected underneath.

On the kitchen side, the extra holes usually exist for a side sprayer, a soap dispenser, or an air gap for a dishwasher. If you’re switching to a modern pull-down faucet that only needs one hole, you’ll have spares to deal with — more on that below. Our full walkthrough on how to choose a kitchen faucet that fits your sink and your life covers matching hole count to spray features in more detail.

What’s the difference between hole size and hole spacing (and why it matters)?

Hole size is the diameter of each individual hole (1‑3/8″); hole spacing is the distance between the holes. These are two completely different measurements, and confusing them is the number one reason people order the wrong faucet.

Think of it this way: every hole on almost every American sink is the same 1‑3/8″ diameter. What changes from sink to sink is how many holes there are and how far apart they sit. So when a product listing says “8‑inch widespread,” it is talking about spacing, not the size of the hole you drill. When it says the faucet fits a 1‑3/8″ hole, it’s talking about diameter.

  • Diameter (1‑3/8″) determines whether the faucet physically passes through the hole.
  • Spacing (4″ or 8″) determines whether a multi-piece faucet’s handles and spout line up with the holes.

For a single-hole faucet, spacing doesn’t matter at all — you only care about the 1‑3/8″ diameter. For a widespread faucet, both matter: each of the three pieces drops through its own 1‑3/8″ hole, and those holes must be 8″ apart (or match the faucet’s rated spread).

My sink has more holes than the faucet needs — what do I do?

Use a deck plate (also called an escutcheon or base plate) to cover the extra holes. This is the easiest and most common fix, and Glacier Bay single-hole faucets are frequently sold with an optional deck plate exactly for this reason. A 4‑inch deck plate lets a single-hole faucet sit on a 3‑hole centerset sink; a longer plate covers a wider spread.

Your options, from easiest to hardest:

  1. Add a deck plate. Slide the plate over the faucet base before mounting. It hides the flanking holes and gives a clean, finished look. Match the plate finish to the faucet.
  2. Use hole-cover buttons. Stainless or finished caps that snap into an unused 1‑3/8″ hole. Good for a kitchen sink’s leftover sprayer hole when you don’t want a sprayer.
  3. Repurpose the extra hole. Install a soap/lotion dispenser, a filtered-water tap, or an air gap. If you’re adding a filter, our roundup of the top under-sink water filters worth buying pairs naturally with a spare deck hole.

The reverse problem — a sink with fewer holes than your faucet needs — is harder. You’d have to drill new holes at the correct spacing, which is doable in stainless steel or a stone countertop but not recommended in porcelain. In that case, it’s usually smarter to choose a faucet that matches the holes you already have.

How do I measure my sink for a replacement Glacier Bay faucet?

Grab a tape measure and check four things: the number of holes, the hole diameter, the spacing between the outer holes, and the deck thickness. Those four numbers guarantee a fit. Here’s the routine:

  1. Count the holes. Look at the top of the sink deck — 1, 2, 3, or 4. Don’t forget a hidden sprayer hole toward the back.
  2. Measure hole diameter. It should be about 1‑3/8″ (35 mm). This confirms a Glacier Bay faucet’s shank will fit.
  3. Measure center-to-center spacing. From the middle of the leftmost hole to the middle of the rightmost hole. ~4″ = centerset; 6–16″ = widespread.
  4. Measure deck thickness. The combined thickness of your sink deck plus countertop. Most faucet mounting shanks handle up to about 1‑3/4″ to 2‑1/4″. Thick stone counters occasionally need an extended mounting kit.

One more real-world tip: before you close up, check the clearance under the sink too. The supply-line connections and mounting nut need room to turn. This matters more with the wrench-in-a-cabinet reality of a vanity than with the hole size itself. If you’re replacing worn parts rather than the whole faucet, browsing the correct faucet replacement parts and how to install them guide shows how mounting hardware is standardized across brands.

Does a Glacier Bay kitchen faucet use a different hole size than a bathroom faucet?

No — the mounting hole diameter is the same 1‑3/8″ for both Glacier Bay kitchen and bathroom faucets. What differs is the number of holes and the accessories, not the size of each hole. Kitchen setups just tend to involve more holes because of sprayers, soap dispensers, and dishwasher air gaps.

A modern Glacier Bay pull-down or pull-out kitchen faucet is almost always a single-hole design, dropping through one 1‑3/8″ hole. Older or more traditional kitchen faucets used a 3‑hole, 8‑inch spread with a separate spout and two handles. So if you’re upgrading from a dated 3‑hole kitchen faucet to a sleek single-hole pull-down, you’ll have two extra holes — cover them with a deck plate (many Glacier Bay pull-downs include one) or add a soap dispenser.

Bar and prep faucets follow the same 1‑3/8″ rule but are usually single-hole by default. Whatever the style, the hole you drill or the hole your sink already has is the same diameter — the brand and category don’t change that.

Glacier Bay faucet hole size vs. other common brands

Glacier Bay’s hole requirements are identical to the major brands because they all follow the same ASME A112.18.1 / CSA B125.1 faucet standards. If you’ve fit a Moen, Delta, or Kohler before, you already know the drill — literally.

Brand Standard mounting hole Common configurations
Glacier Bay 1‑3/8″ (35 mm) Single-hole, 4″ centerset, 8″ widespread
Moen 1‑3/8″ (up to 1‑1/2″) Single-hole, centerset, widespread
Delta 1‑3/8″ (up to 1‑1/2″) Single-hole, centerset, widespread
Kohler 1‑3/8″ (35 mm) Single-hole, centerset, widespread

The practical takeaway: because the diameter is standardized, you can usually swap a Glacier Bay faucet into a hole that previously held a different brand without redrilling — as long as the hole count and spacing match your new faucet’s configuration.

A quick word on installation and getting it right the first time

Once your hole size and spacing check out, the install itself is beginner-friendly. Drop the faucet through the hole, secure it with the mounting nut from below, connect the supply lines (Glacier Bay faucets typically use standard 3/8″ compression connections), and turn the water back on to check for leaks. If you’re comfortable with a basic supply-line hookup — the kind covered in our guide to the brass faucet quick connect — you can handle a faucet swap in under an hour.

The mistakes that cause callbacks almost never involve the hole diameter. They’re loose mounting nuts, over-tightened supply lines, or a widespread faucet installed on a centerset sink. Measure twice, and you’ll avoid all three.

FAQ

What size is a standard Glacier Bay faucet hole?

A standard Glacier Bay faucet requires a 1‑3/8 inch (35 mm) diameter mounting hole. This matches the U.S. residential standard, so the faucet’s shank and hardware fit sinks and countertops drilled to that size. Holes up to about 1‑1/2″ also work because the base and gasket cover the extra clearance.

Will a Glacier Bay faucet fit a 3-hole sink?

Yes. A 3‑hole centerset Glacier Bay faucet fits a 4‑inch, 3‑hole sink directly. A single-hole Glacier Bay faucet also fits a 3‑hole sink if you add a deck plate to cover the two outer holes — many models include one in the box.

Can I install a single-hole faucet on a sink with more holes?

Absolutely. Use a deck plate (escutcheon) sized to span the existing holes, or fill the unused holes with finished hole-cover buttons, a soap dispenser, or a filtered-water tap. The single-hole faucet mounts through the center hole and the plate hides the rest.

How do I measure the hole spacing on my sink?

Measure from the center of the leftmost hole to the center of the rightmost hole. About 4 inches means you have a centerset sink; 6 to 16 inches means widespread. This spacing tells you which multi-piece faucet configuration to buy — it’s separate from the 1‑3/8″ hole diameter.

Do I need to drill a bigger hole for a Glacier Bay faucet?

Usually not. If your existing hole is 1‑3/8″ or slightly larger, the faucet fits as-is. You’d only drill if the hole is smaller than 1‑3/8″ or if you need to add holes for a widespread setup. Drilling stainless steel or stone is manageable with the right hole saw, but drilling existing porcelain risks cracking, so match the faucet to your holes when you can.

Are Glacier Bay hole sizes the same as Moen or Delta?

Yes. Glacier Bay, Moen, Delta, and Kohler all use the 1‑3/8″ standard mounting hole and the same 4‑inch centerset and 8‑inch widespread spacing, because they follow the same ASME/CSA plumbing standards. You can typically swap between brands without redrilling as long as the hole count and spacing match.

Author note & brand credibility

Written by the product team at gotonovofaucet, where we’ve spent years sourcing, testing, and fitting faucets across kitchens and baths. Every dimension in this guide reflects the North American ASME A112.18.1/CSA B125.1 standards that Glacier Bay and other major brands are certified to. At gotonovofaucet.com we build and stock faucets designed to drop into these same standard hole sizes, and our fixtures are backed by manufacturer warranties and independent finish-durability testing. When in doubt about a specific model, always confirm the hole spec on the product’s spec sheet before drilling.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top